Your garage door is the primary entry point used daily; a smooth functioning garage door is crucial in ensuring the overall upkeep of your home. Like anything in a home, your garage door is exposed to wear and tear from time to time. It is crucial to know the signs of broken garage door springs and have them replaced so that your garage door can function normally. Seeking professional help in replacing the door springs is essential to prevent injuries. Here are some tell-tale signs that your garage door springs are broken.
The garage door seems slow or heavy
If your garage door feels heavy and shows difficulties in opening or does not open completely, then the door springs are broken. You can also check your sensors to see if your safety system was triggered. In case of broken door springs, you will need to contact a specialist to replace the springs.
Garage door cables appear broken
Door cables usually located on both sides of the door, wrapped around a drum that moves when opening and closing the door. In most cases, the broken cable will fly around in different ways, and this will make the door disconnected. You will need to look at the springs to determine if there is a broken torsion spring. You can also lift the door manually to see if there is a broken spring.
Garage door stops 6-inches above the ground
You will not know you have a broken garage door is until when you try to open it. The door will open slowly and stop 6-inches or a few inches above the ground. That is because when there is a broken door spring, system sensors are activated to prevent further damage to the door. You are advised to close the door and pull the release rope to move the door since a crashing door can cause massive problems.
The garage door produces a heavy, loud sound
When one of the torsion springs unwind, they create a loud noise due to the coils spinning on the shaft. You will hear a loud bang in the garage area, and you may think that robbers are breaking into your home. You check around and do not notice anything until the next day when you will face difficulties opening the garage door.
There is a 2-inch gap in your torsion springs
Broken springs always show a 2" gap in the middle of the torsion springs. Therefore, this issue is caused by compression of the spring, causing the metal to leave a 2-inch gap when the spring breaks. You can check the hole when the garage doors stop functioning correctly.
The garage door falls going down
The torsion springs hold the door weight, and this controls the speed at which the door closes. If there is a broken door spring, the door will close faster, which is very risky and needs repair.
The top section of the garage door is bent
Depending on the type of garage door you have installed, the door bends in the top section, this is a sign of broken door springs. Thereby it is caused by an open force that turns to the circuit board. Replacing the top part might be costly, so if you see any bends, make sure you have the springs replaced to keep the door intact and robust.
The garage door can't open using the emergency rope
There is an emergency rope hanging on the side of your garage door. The door works in an open mechanism such that if you pull the string down the door starts opening upwards. If you remove the rope and the door fails to open, then your spring is most likely broken. You can also try to lift the door, and if it does not move upwards freely, then you will need to have the springs replaced.
Leaning garage door
Your garage door might look crooked; this is as a result of damaged spring extensions. When the door is closed, you will find it leaning, one side nearer to the ground than the other. If you also open the door, you will realize the same. That is a sign of broken door springs.
The door jerking when moving
Have you ever tried opening your garage door then you find it jerky? This is a common sign of broken spring extensions. Replacing the springs will eliminate this problem.
What do you do if you have a broken garage door spring?
If you have broken garage door springs, you will need to contact a professional as soon as possible. Do not repair it on your own since replacing broken garage door springs may be dangerous when done without the recommended tools. Here is the process of replacing broken door springs:
Disarm the spring – the first step when replacing broken torsion springs is to remove the damaged springs. This is the most dangerous step, to securely transfer the tight springs, you might get injured thus you need a specialist.
Costing and setting up the door – the step involves checking the integrals of the door and the rails and ensuring there is alignment before installing new springs. Connection of appropriate sections of the spring is made to ensure its securely attached.
Test – after completing the installation, the door is in place, you will carry out multiple checks to ensure the door is working correctly. Open and close the doors to see the reaction of the new springs.
Follow up – Ensure the technician follow up from time to time to ensure the door is intact and no broken springs.